20Khz wide frequency ultrasonic generator for ultrasonic machining

Descriperson

Power Supply. Every ultrasonic welder starts with a power supply. The power supply is sometimes referred to as the frequency generator because it takes standard electrical power (usually 115V) at 60 Hz and converts it to the operating frequency of approximately 20 kHz or 20,000 cycles per second. Other output frequencies commonly available range from 15-70 kHz. This high frequency current is then sent through a special cable to the ultrasonic stack.

Ultrasonic Stack. The stack is not one thing, but rather the combination of three core components: the converter, booster, and weld horn. In a plastic welder, the ultrasonic stack is aligned vertically and sits above the parts being welded in a supported column.

This digital generator is available in frequencies of 15kHz, 20Khz, 28Khz,30 kHz, 35 kHz and 40Khz at a power range between 300 W and 3000 W. Programmable ramp up and ramp down times and infinitely variable adjustment of weld amplitudes are only some of the features of this product line. The biggest advantage of this generator is the wide frenquncy range, for example: the 20Khz generator, it can catch the frequency from 18~21khz, so it is easy to tuning. Also it is easy for some ultrasonic new user.

100% digital control of all power supply functions and parameters allows for unique configurations and future upgrades or requirements. Includes digital frequency syntheses
Industry leading data acquisition rate speed of .5 ms due to advanced multi-core architecture. Increased weld accuracy and repeatability.

Application

Sonic & ultrasonic transducers are electro-mechanical or electro-acoustic converters. They transform electric energy into vibrations, which are used to generate mechanical, acoustic or even thermal power. Sonic transducers operate at audible frequencies, while ultrasounds operate at 20kHz or above. Transducers are often reciprocal devices: Most transducers can operate as sensors or generators exploiting mecano-electric conversion. This section introduces only actuation or emission modes. Conversion in such transducers is generally based on piezoelectric, magnetostrictive or magnetic forces.
The most conventional approach consists in using such forces to excite a mechanical resonance. For the same electric excitation, the vibration at resonance is the low frequency vibration multiplied by the mechanical Quality factor at resonance. This allows to achieve a good efficiency and reduced excitation voltages. The alternative way is to generate forced vibrations. Forced vibrations lead to large frequency bandwidth and are much less sensitive to load variations.
The usual ultrasonic transducers also called industrial ultrasonic processors are resonant structures typically based on 3 half-wave length resonators : a piezo converter, a booster and a sonotrode. They are used for ultrasonic welding, milling, cleaning, nebulization or ultrasonic assistance in drilling, extrusion, homogeneisation, filter declogging…HC-SONIC can define solutions using standard transducers. Customisation is often required to adapt the sonotrode to the load as shown below.
A new approach consists in using new active materials such as multilayer piezo ceramics (MLA) or giant magnetostrictive materials (GMM). These are used to build low frequency resonant transducers in dual-mass Tonpilz structures.

Power requirements

The power input standard is: single-phase AC220V 50HZ/60HZ.
Input power supply voltage fluctuation range: <10%.
Input power supply harmonic content: <20%.
Input power supply current: 10A.
Input power cord diameter: >1.5MM2.

R-Responsibility P-Products S-Service

sale the right products instead of the expensive one

Rps-sonic, consisted with a couple of young people who love ultrasonic very much.The founding members of RPS-SONIC have an average degree of Bachelor's degree or above. They have been in the ultrasonic industry for more than 5 years and have rich experience in ultrasound. The company's business philosophy is: Do not blindly promote any product, find the right product for the customer. So before each order, we will confirm all the details, including application details, equipment conditions, equipment specific information.

And we have the Professional import and export company， HangZhou LanBen Trade Co., Ltd, can export to any country wordwide.

Before year 2012, we only sale second branson / dukane / rinco / herrman/telsonic welding equipment , during these twenty year develop, we find, more and more people have problem with the core part of ultrasonic welding equipment -generator and transducer, so we decided to start our business of transducer and generator of our own transducer and generator. Many of the end user meet the transducer problem, they don’t know why transducer broken, and changing the expensive transducer one by one. Actually, one branson /dukane /rinco transducer can use 10~30 year, even the cheapest transducer can use about 5 years. So there must some reasons if your transducer broken in one year. That’s why we want build Rps-sonic, we need to help more end user to know more about transducer , to use ultrasonic equipment better, to save cost when meet problem.

The same to generator, Unreasonable operation may shorter the use-life of ultrasonic generator. So we have to make technical inquiry before operate ultrasonic welding machine. The key point of ultrasonic machine is resonance, only keep every part in resonance can make the system in best work environment.

Till now , we still have a lot of Branson /dukane/ rinco/ herrman telsonic welding machine, so that we can confirm every transducer/generator we made can matching to the original machine.

Of course we can make the transducer/generator replace for Branson /dukane/ rinco/ herrman telsonic welding machine, we can also make transducer/generator for any application of your ultrasonic equipment. We supply OEM service for oversea customers, we already have OEM customer in USA and German.

If you have any problem in ultrasonic area, welcome contact Rps-sonic.